The writer is making a number of great points on Tools You Need to Install a New Bathtub as a whole in the article underneath.
Setting up a bath tub isn't specifically brain surgery, but it does call for strong plumbing, woodworking, as well as sometimes, tiling skills. Changing an old bath tub with a new one is likewise a moderately difficult job. If the old tub is easily accessible, the project can move easily; if you need to open a wall to eliminate the old tub and place the brand-new tub, the task is much harder. In either case, the project is within a house handyman's skills, although you will require a helper to leave the old tub and also set in the new one. See to it you have certified yourself for the task as well as fit attempting it. Instead of working with a professional to take over a halfway-completed project, it is far better to consider using one before you start. Chances are you may need a specialist plumber to make tube connections.
This short article will certainly aid you set up a brand-new bathtub in your restroom if you have already acquired a brand-new tub and do not need to alter the setup of your previous supply of water pipelines.
Your devices as well as material checklist should comprise the following:
Planning for the Installment
To start with, the sustaining structure supplied with the bath ought to be fitted (if called for) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to make sure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets unit to avoid strain on the bath tub.
Fit the adaptable tap connectors to the bottom of the two taps making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its final setting.
Removing Old Taps
If you require to replace old taps with new ones as a part of your setup, after that the first thing you should do is separate the water system. After doing so, activate the taps to drain any water continuing to be in the system. The process of eliminating the existing faucets can be rather bothersome as a result of the limited gain access to that is typically the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly come from the pipes. As soon as the supply pipes have been removed, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. As soon as the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any kind of old securing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, put the bathtub in the called for setting. The wood boards are handy in uniformly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The next objective is to make certain that the tub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the tub till the spirit level reads degree.
To install faucets, fit the bottom of the outermost flexible tap adapter to the proper supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Activate the water system and examine all joints and also new pipework for leakages and also tighten them if required. Load the tub and likewise examine the overflow electrical outlet as well as the normal electrical outlet for leaks.
Lastly, repair the bathroom paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bath tub needs to wait till the tub has actually been utilized at the very least once as this will certainly settle it into its last placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end gives a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin making sure that the washers remain in location between the tap and also the sink. Safeguard the faucet in place with the maker provided backnut. Once the faucet is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular faucet connectors. The previous kind needs to be linked to the tap finishes first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to crack an inflexible seal, creating the water to penetrate the wall surface between the bathroom as well as the tiling, causing difficulties with moisture as well as possible leakages to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your components and also fittings. They are marketed in tubes and also cartridges, as well as are capable of securing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of soaked paper or soft rope. Remember to constantly load the tub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealant can split relatively very early if you do not consider this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly offered on the marketplace. It is advisable to fit the floor tiles making use of waterproof or water resistant sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading about A Step-by-Step Guide to Installing a Bathtub? Create a comment further down. We will be delighted to know your ideas about this posting. Hoping to see you back again soon. Sharing is nice. You never know, you might be helping someone out. Kudos for your time. Kindly come by our site back soon.
Call for peace of mind!